Skip to main content
TRACEFORMEmergency Electricians
Bathroom and kitchen fans

Extractor Fan Not Working? Repair and Replacement in Manchester

Smoke or burning from the fan: leave and call 999. If your extractor fan is not working, we find out why it has stopped, will not stop or turned noisy, then repair or replace it.

Most fan faults sit in the motor, the controls or the wiring to the light. We test all three first.

Call-out from£110simple fault (first hour) · agreed before we travel · see prices

  • Bathroom, kitchen and loft fans
  • Timers and humidistats set up
  • Wiring and isolator checked
  • Tested before we leave
  • Under 60 minGreater Manchester
  • NICEIC registeredverified & trusted
  • Qualified & insuredfor your peace of mind
  • Local coverageGreater Manchester, Liverpool, London, Cambridge & Peterborough
Request a callback
TRACEFORM electrician on a step ladder fitting a new ceiling extractor fan in a bright tiled bathroom
Fan, controls and wiringA dead or stuck-on fan is often a control or wiring fault rather than a worn-out motor, so we test before we replace anything.

Why is my extractor fan not working?

An extractor fan not working is most often down to an isolator left off, a blown fuse in its spur, a failed timer board or a seized motor. A simple fault repair is typically £110–£185, quoted before work starts. We test the fan, its controls and wiring, then repair it or fit a correctly rated replacement.

Manchester, Liverpool, Cambridge & Peterborough prices

Typical prices

Your call-out price is agreed on the phone before an engineer travels. Any repair is explained and priced for your approval before work starts.

  • NICEIC registered
  • Price agreed first
  • Fault findingSimple fault (first hour)£110–£185
  • Planned work ratesHourly rate£55–£75
  • Emergency call-outsWeekday daytime£110–£150
Do this first

An extractor fan not working shows as a mirror that never clears, a fan that hums but barely turns, or one that runs half the night. We check the fan, its timer or humidity control and its wiring, then price the repair before work starts.

What to do first if the fan stops, sticks on or smells

  • Smoke, flames or burning smell: leave the room, close the door and call 999.
  • Switch the fan off at its isolator only if that is dry and easy to reach. Otherwise use the consumer unit, only if it is dry and safe to reach.
  • Do not open the cover or touch a fan that is wet, hot or dripping. Water through the ceiling also needs a plumber.
  • A fan that simply will not start is not an emergency. Open the window after showering and book a repair.
Safety Notice

Do not open a fan cover or touch a fan that is wet, hot or smells of burning. For smoke or flames, leave and call 999.

Still stuck? Call 07777 301818
Diagnostic view

Schematic illustration of how this fault is traced during diagnosis.

Signs your extractor fan needs an electrician

What the fan is doing usually points to the fault.

The bathroom light comes on but the fan stays silentIsolator off, blown spur fuse, or failed motor or timer.
The fan keeps running long after the light is off, or never stopsOverrun timer, humidistat setting or switched live wiring.
Rattling, grinding or a loud hum from the grilleWorn bearings, dusty impeller or loose mounting.
Steam and condensation hang about even with the fan runningBlocked or crushed duct, or a fan too small for the room.
The lights or the RCD trip when the fan startsWater inside the fan or a wiring fault to earth.
The kitchen wall fan or cooker hood has no power at allTripped circuit, blown fuse or failed supply connection.
Describe what you are seeing
Right now

Repair or replace?

What the fan does points to the cause, and the cause decides repair or replacement.

Repair or replace?
What the fan doesLikely causeUsual answer
Dead, but the light worksIsolator off, blown spur fuse, loose connection or failed timer or motorRepair if the supply is at fault; replace if the motor or board has failed
Runs but never stopsOverrun set too long, humidistat too sensitive, crossed switched live or failed timerReset or rewire the controls; replace only if the board has failed
Very noisy or rattlingWorn bearings, dust on the impeller, loose mounting or a flapping shutterClean and secure if the motor is sound; replace if the bearings are worn
Runs but does not clear steamCrushed or detached duct, blocked grille, no air path or an undersized fanFix the duct first; replace with a stronger fan if it is too small for the room
Trips the lights when it startsWater inside the fan, a damaged motor or a wiring fault to earthIsolate and test; a wet or burnt fan is replaced, never dried and refitted

Dead, stuck-on or noisy fans are often repairable once controls and wiring are tested. A seized, wet or undersized fan is better replaced.

Sources: Ventilation: Approved Document F (GOV.UK), Bathroom electrical safety (Electrical Safety First)

How we repair an extractor fan

From your call to a fan that starts, stops and clears the room.

  1. Tell us what the fan is doing

    Does the light still work, does the fan hum or run on, and where is the isolator? The call-out price is agreed on the phone before we travel.

  2. Isolate and test the supply

    We prove the fan dead, then check the isolator, any fused spur and the permanent live, switched live, neutral and earth against the fan's wiring diagram.

  3. Check the fan, controls and duct

    Impeller, bearings, backdraught shutter, timer or humidistat board and the duct run all tell us whether a repair or a new fan is the honest answer.

  4. Repair, test and hand over

    The repair is priced first and, where parts allow, done on the same visit. We test insulation resistance, polarity, protective conductor continuity, earth fault loop impedance and RCD trip time, then run the overrun.

Bathroom extractor fan not working but light is

Most bathroom fans come on with the light. A fan with an overrun timer needs a permanent live to stay powered and a switched live from the light switch to tell it when to start. Both usually pass through a three-pole fan isolator, often a small switch outside the bathroom that people mistake for a spare light switch and turn off.

So we start there: an isolator off or failed, a blown fuse in a fused spur, a loose connection, or a switched live that never reaches the fan. If the supply is healthy, the timer board or motor has usually failed. A fan that hums without turning normally has seized bearings.

Extractor fan not turning off

Running on for 15 or 20 minutes is normal, and Approved Document F expects at least 15 minutes in a room without an openable window. A fan that never stops usually has its overrun at maximum, a failed timer board, or its switched live and permanent live crossed. Some modern fans are designed to tick over all day and boost when needed, so check before switching one off.

When the extractor fan humidistat is the cause

An extractor fan humidistat starts the fan above a set humidity and often overrides the timer. Set too sensitive, or coated in dust, it can run for hours in a damp house. We adjust the setting, check the sensor and replace the fan or module if the board has failed.

Noisy extractor fan or one that does not clear steam

A noisy extractor fan is usually worn: grinding means tired bearings, a whine means a motor fighting a blocked duct, tapping in wind is often the backdraught shutter. Loft inline fans can drum against joists when mountings loosen.

If it sounds fine but steam hangs about, check the air path. Loft ducting gets crushed or pulled off, outside grilles block, and a door with no gap underneath starves the fan. Approved Document F sets minimum intermittent extract rates of 15 litres per second for a bathroom and 30 or 60 for a kitchen, depending on the cooker hood.

Kitchen extractor fan not working

Kitchen fans fail in the same ways, with grease added. For cooker hoods we handle the electrical side: the fused connection unit or switch, the flex and the supply. If the supply is healthy and the hood has failed, we tell you so you can arrange the appliance repair.

Bathroom extractor fan replacement

A bathroom extractor fan replacement starts with a fan with enough airflow and the right controls: timer, humidistat, pull cord or occupancy sensor. In zones 1 and 2 it needs a suitable IP rating, and some positions call for a SELV fan with its transformer outside the zones. We confirm RCD protection, keep the isolator out of reach of the bath and shower, and check the duct.

A swap on existing cabling is usually straightforward. A new fan on a new cable route may be notifiable under Building Regulations Part P; we tell you before starting and supply the certificates.

What the guidance says about extract fans

Why people call us for fan repairs

A small job with wiring that is easy to get wrong.

Cause found first

Controls and wiring are tested before the fan is blamed.

Bathroom zones respected

Replacements carry the right IP rating, or are SELV where the position needs it.

Price agreed before work

Call-out agreed on the phone; repairs priced on the spot.

Day or night

Typically under 60 minutes in Greater Manchester, Liverpool, Cambridge and Peterborough, under 2 hours in London.

Repairs and replacements

Ceiling, wall, window and loft inline fans, plus cooker hood supplies.

Timers and humidistats

Overrun and humidity settings set so the fan stops when it should.

Safe isolation

A three-pole isolator or fused spur where one is missing or failed.

Extractor fan questions

Common questions about extractor fans.

Why does my bathroom fan only work when the light is on?
It was either fitted without an overrun timer, or the permanent live that keeps it running is missing. We can add one through a three-pole isolator or fit a timer fan.
What is the small switch outside my bathroom door?
Usually a three-pole fan isolator, which cuts all supplies to the fan for safe work. If it is off, the light works and the fan does not.
Can a humidistat fan that keeps running be fixed?
Often it only needs the humidity setting adjusted, which sits behind the cover, so leave it to an electrician who can isolate the fan. If it still never stops, the sensor or board has failed.
How much does it cost to repair or replace an extractor fan?
A simple repair is typically £110–£185, quoted before we start. A replacement is priced on the spot once we have seen the position, duct and wiring. Adding a fan where there was none is planned work at £55–£75 plus parts.
Is a fan right above the shower allowed?
Yes, if it has an IP rating suited to water spray, and some makers require a SELV version. The isolator must be out of reach of anyone in the bath or shower.
Why does water drip from my extractor fan?
Usually condensation in a cold loft duct running back into the fan. Switch it off at the isolator if that is dry and safe to reach, and have the duct and fan checked.
Should a landlord fix a broken extractor fan?
In most tenancies the landlord keeps fixed installations such as extract fans working. Tenants should report it in writing; we can attend on the landlord's or agent's instruction. A dead or switched-off fan is a common reason condensation turns into mould in rented homes. Tenants often switch noisy fans off at the isolator, so a quieter replacement tends to stay on. We send a written note of what we found and did.

Secure callback request

Request a callout

Share your details and an electrician will call you back. Typical response under 60 minutes.

  1. 1 · The problem
  2. 2 · Your details

Step 1 of 2: the problem

What do you need help with?
How urgent is it?
Photos of the problemoptional · up to 5

A photo of the fuse box or fault helps us bring the right parts. Location data is removed.

  • NICEIC
  • 24/7
  • Clear prices

Your details are only used to respond to your enquiry

Greater Manchester coverage

Check your area

Enter a full UK postcode to confirm we cover your area and can respond quickly.

  • Greater Manchester, Liverpool, London, Cambridge & Peterborough
  • Surrounding areas
24/7 emergency electricians

Fan dead, stuck on or noisy?

Tell us what it is doing and where the isolator is. We agree the call-out first and price the repair before we start.