Skip to main content
TRACEFORMEmergency Electricians
Leaks, lights and wet circuits

Water Leaking Into Electrics? We Make It Safe, 24/7

For smoke, sparks or burning, leave and call 999. Water leaking into electrics means switching that circuit off at the consumer unit, only if the board is dry and safe to reach. We then trace, dry, test and restore the power.

Bath overflow, burst pipe, washing machine, loft or the flat above: we find which circuits got wet and keep the rest on.

Call-out from£110weekday daytime · agreed before we travel · see prices

  • Wet circuits isolated, dry ones kept on
  • Insulation tested before power returns
  • Damaged fittings replaced and retested
  • Under 60 minGreater Manchester
  • NICEIC registeredverified & trusted
  • Qualified & insuredfor your peace of mind
  • Local coverageGreater Manchester, Liverpool, London, Cambridge & Peterborough
Request a callback
TRACEFORM electrician checking a water-stained ceiling light with a moisture meter as a homeowner holds towels below
Do not touch the wet fittingTurning the light switch off does not make a wet fitting safe. Isolate the circuit at the board if it is dry, or keep everyone away and call us.

What should I do if water is leaking into electrics?

Water leaking into electrics should be treated as live danger: keep clear of wet fittings and switch the circuit off at the consumer unit only if the board is dry and safe to reach. A weekday daytime call-out is typically £110–£150, agreed before we travel. We isolate, dry, test and restore what is safe.

Manchester, Liverpool, Cambridge & Peterborough prices

Typical prices

Your call-out price is agreed on the phone before an engineer travels. Any repair is explained and priced for your approval before work starts.

  • NICEIC registered
  • Price agreed first

Emergency call-outs

First hour on site, including the call-out.

  • Weekday daytimeLowest price£110–£150
  • Weekday evening£150–£220
  • Night£175–£245
  • Weekend daytime£160–£235
Safety Notice

Never touch a wet light, switch or socket, and stay away from the consumer unit if it is wet or you would have to stand in water to reach it. For smoke, sparking or burning, leave and call 999.

Right now

Water in the electrics: what to do right now

Start at the top: people first, then the water, then the electrics. Find the row that matches what you can see.

Water in the electrics: what to do right now
What you can seeDo this nowWhat we do
Smoke, sparks or a burning smellGet everyone out and call 999. Do not go back in to switch anything off.Once the fire service says it is safe, we isolate the affected circuits and test them before anything is restored.
Water still coming throughStop the water at the stopcock if you can reach it safely, and call a plumber for the leak itself.Isolate the circuits in the leak path so the plumber can work safely, and keep the dry circuits on.
Water in a light fitting or dripping from a lightDo not touch the light or switch: the switch breaks only one wire, so the fitting can still be live. Switch the circuit off at the consumer unit if the board is dry and safe to reach.Isolate the lighting circuit, drain and inspect the fitting, then test insulation before anything is restored.
Water on or near the consumer unitDo not touch the board. Keep everyone out of that room and call us.Arrange isolation from a safe point, dry and inspect the board, and replace any wet or damaged parts.
RCD trips after a leak and will not resetStop trying to reset it. Note which switch tripped and what was running when it went.Split the circuits, find the wet one with insulation testing and restore the dry circuits first.
Water stopped, ceiling stained, power onAvoid using the lights in that area and book a check. Keep an eye on the stain spreading.Open the fittings near the stain, look for corrosion and test the circuit while the ceiling dries.
Leak from the flat aboveTell the neighbour or managing agent so they can stop it, and switch off your affected circuit if the board is dry.Make your side safe, keep dry circuits on, and give you notes for the landlord or insurer.

If you are unsure whether a wet fitting is safe, treat it as live and keep away.

Sources: Electrical safety after a flood (Electrical Safety First), Private renting: repairs (GOV.UK)

Diagnostic view

Schematic illustration of how this fault is traced during diagnosis.

Signs water has reached your electrics

Signs that water has reached the wiring, and what each usually means.

Water dripping from a ceiling light, downlight or ceiling roseWater has reached live terminals; isolate the circuit.
A brown stain or bubbling paint around a light fittingWater has been there a while; terminals may be corroding.
The RCD tripping during or after a leak and refusing to resetCurrent is leaking to earth through a wet circuit.
Lights buzzing, flickering or failing in the room under a bathroomMoisture in a fitting or junction box above.
Water running down a wall past a switch or socketThe back box may be wet even if the front looks dry.
Damp, a musty smell or water marks near the consumer unitNeeds an urgent inspection before anyone touches it.
Describe what you are seeing

How we make electrics safe after a leak

From your call to circuits that are dry, tested and back on.

  1. Tell us what you can see

    We ask where the water is coming from, which fittings are wet, whether the RCD has tripped and whether the board is dry, then tell you what to switch off while you wait. The call-out price is agreed before we travel.

  2. Trace where the water has gone

    We check ceilings and walls with a moisture meter and identify every circuit the water may have reached, including hidden junction boxes.

  3. Isolate and make safe

    Wet circuits are isolated and proved dead, fittings are opened and drained, and dry circuits are tested and kept on. Where a ceiling may come down, the fitting is disconnected and the cable ends are made safe.

  4. Test, repair and restore

    Insulation resistance, continuity, polarity, loop impedance and RCD trip times are checked. Damaged accessories are replaced, where parts allow on the same visit, and you get the paperwork the job needs.

Water leaking into electrics follows cables, joists and conduit, so the fitting that drips is rarely the only one affected. We stop the danger, let things dry, prove the wiring with proper tests and only then restore power.

Why water leaking through light fitting points is so common

Ceiling lights sit at the lowest point of a wet ceiling. Water from a shower tray, the flat above or a roof leak runs along the plasterboard to the nearest hole, usually a ceiling rose or downlight cut-out. Junction boxes in the loft or floor can fill with no sign below, and wet terminals can corrode and work loose weeks later.

Electrics tripping after a leak: what the RCD is telling you

Water lets current leak from the live or neutral conductors to earth, and the RCD trips. That is the protection working. If it trips again the moment you reset it, the circuit is still wet or damaged, so leave it off. A trip only when the shower or washing machine runs means water is still getting in.

Testing before anything is switched back on

The key test is insulation resistance, which shows whether current can leak through damp insulation or wet accessories. We also check continuity of protective conductors, polarity and earth fault loop impedance, and time the RCD. A circuit goes back on only when the readings are sound. If they are borderline, it stays off to dry and we retest.

How long electrics take to dry after a leak

A fitting that had a short drip of clean water may test sound the same day once opened and drained. A soaked ceiling or a junction box that sat in water can take several days. We tell you what can be used now and come back to retest the rest.

Electrical damage from water leak: what usually gets replaced

Clean water from a burst pipe or tank often needs only drying and new accessories where it reached. What we commonly replace:

  • Ceiling roses, downlights and pendants with staining or corroded terminals
  • Switches and sockets on walls the water ran down
  • Junction boxes and connectors in the loft or floor void
  • Short lengths of cable with a damaged sheath or blackened copper

Waste water, or water that has sat in a consumer unit, can mean replacing more. Repairs are quoted on the spot before work starts, and we can write a damage report if your insurer needs one.

What the official guidance says

Why our approach to leaks keeps you safe

A leak is a plumbing problem first, but the electrics are what can hurt someone.

We follow the water

Leaks travel along cables and joists, so we check the fittings and junction boxes around the drip too.

Tested before it goes back on

Insulation resistance and RCD tests decide when a circuit is restored, rather than a guess that it looks dry.

Dry circuits stay live

Only what got wet is isolated, so the fridge, heating controls and safe lighting stay on.

Day or night

Typically under 60 minutes in Greater Manchester, Liverpool, Cambridge and Peterborough, and under 2 hours in London.

Make safe tonight

Wet circuits are isolated so nobody touches a live part while the ceiling dries.

Paperwork for the job

Test results and notes for a landlord, agent or insurer.

Who calls us about leaks into the wiring

Leaks happen in every kind of building. The make-safe is the same.

More on water and electrics

Short guides on wet electrics, weather damage and why protection trips.

Secure callback request

Request a callout

Share your details and an electrician will call you back. Typical response under 60 minutes.

  1. 1 · The problem
  2. 2 · Your details

Step 1 of 2: the problem

What do you need help with?
How urgent is it?
Photos of the problemoptional · up to 5

A photo of the fuse box or fault helps us bring the right parts. Location data is removed.

  • NICEIC
  • 24/7
  • Clear prices

Your details are only used to respond to your enquiry

Questions about water and electrics

Questions people ask while holding a bucket under the light.

Is it safe to leave the lights on if water came through the ceiling?
No. Water inside the fitting can make metal parts or the ceiling around it live. Switch the circuit off at a dry, reachable consumer unit and leave it off until it has been tested.
Will the electrics be fine once the water dries out?
Sometimes, but you cannot tell by looking. Water leaves corrosion on terminals that can cause heat or trips weeks later. An insulation resistance test shows whether the wiring is sound, and corroded fittings are replaced.
How much does it cost to make electrics safe after a leak?
A weekday daytime call-out is typically £110–£150 and a night call-out typically £175–£245, agreed on the phone before we travel. Replacing a single damaged light or accessory is typically £110–£185. Larger repairs are quoted on the spot before work starts.
Who pays for the electrician if the leak came from upstairs?
That depends on who caused the leak, your tenancy or lease and your insurance. If you rent, the landlord is responsible for repairs to the wiring. We give you a clear record of what was wet, tested and replaced to pass on.
Does my insurer need a report on the electrical damage?
Many insurers ask for evidence before agreeing repairs. Photograph the leak and wet fittings from a safe distance, and we can write an electrical damage report with our findings and test results.
Should I turn the main switch off if I do not know which circuit is wet?
If the consumer unit is dry and you can reach it without standing in water, yes. If the board is wet or in the leak area, do not touch it and keep everyone away until we arrive.
Greater Manchester coverage

Check your area

Enter a full UK postcode to confirm we cover your area and can respond quickly.

  • Greater Manchester, Liverpool, London, Cambridge & Peterborough
  • Surrounding areas
24/7 emergency electricians

Water in the lights or the board tripping after a leak?

Keep clear of wet fittings, switch off at a dry consumer unit if safe, and call us. We make it safe, test it and restore what is sound.